Just put your seat in the upright position, pull it in and you are good to go. You may be required to insert your key in order to start operating your slide-out or there could be just a switch. I know it sounds ridiculous but did you have your ignition turned on when you tried to move your slides? The motor doesn’t have to be running just the key turned on. Stay at your location and get a mobile technician to come to you if possible.
During those three repeat in and out motions, those motors find that zero point and can start counting correctly again. To prevent this situation, when you extend or retract the slide-out, you want to press the button for up to 5 seconds longer. If your Lippert slide works the same as my previous one did, the slide switch is a DPDT, center-off, polarity reversing switch. Either the two motor wires or the two power wires go to the switch center terminals. Then the two sets of outer terminals on the switch are connected in crisscross fashion, i.e. upper right to lower left, and lower right to upper left. The power or motor wires, whichever aren’t hooked to the center terminals, connect to either end of the switch’s outer terminals where the crisscrossed wires are.
Table of Contents
Other RV slideout problems
If the battery does read low voltage, you will need to either recharge it or connect a fresh battery to the RV’s electrical system to activate the slide-out system properly. Look closely at the terminals on your RV’s 12 Volt house batteries. Proper electrical current is needed for the power-retractable slide-out mechanisms to work correctly. On some Tiffin models, all you have to do is disconnect the wires to the controllers and the slides can be simply pushed back into place.
Foreign objects on the tracks, insufficient lubrication, and leaks are other common issues with Jayco RVs. You can troubleshoot and solve these problems as described earlier under common issues. You should apply some wax on the slide walls to have the slide fully retracted and then take your RV to a service shop.
Common RV Slide Out Problems and How To Fix Them
After calling a couple of Lake Charles RV repair shops, the initial thought was the slide motor had quit working. I was able to find a new replacement motor (KMG – Klauber Machine Group) from a dealer in Lafayette and found a mobile RV repair company that would work on a Saturday. After the new motor was installed, the slide still would not retract. The “square rods” connected to the motor were detached to assure the new motor was functioning.
These are usually responsible for the entire extending and retracting of your slide-outs. The first thing that you should check when there is an error with your motor is its wires. You can notice this if there are any breaks in between the cable or if it is bent. The most common issue that people run into is that the switch on their slide-out stops functioning. This is essential because it Is used to extend or retract the slide-out from your vehicle.
Slideout Hydraulic System Leak
This information was collected from a variety of sources and is subject to change without notice. We assume no responsibility and disclaim any liability for anyone’s use of the information provided. Hydraulic line components include actuators that move rams and if they fail, the whole system will not work. Damaged valves could be another reason for pumps to malfunction. If there is an obstruction blocking the way that you did not notice, remove the obstacle, or move your RV.
I’ll have to pay more attention to cleanliness in that area in the future because the under-step battery / fuse area is very exposed to the elements, especially when driving. Now is the time to check the main 110-volt circuit breaker. Replace the breaker wires if they are faulty and have power. Make sure to check the breaker connection to avoid any issue such as RV plugged in but no power. Missing a circuit to supply power to slideroom motor.The drawing pictures one relay to power the in and out voltage to the motor- there are 2 power relays.
What to Do When Your RV Slide-Out Sections Goes Out But Not Back In
If you are experienced, then you most likely don’t need any guides. This is one of the most asked questions regarding the batteries charging and the answer is yes. With the availability of many options on how to charge your RV batteries, one of the well-known ones is to simply plug it into your 110V power shore. Lastly, one important thing you should always bear in mind is your own SAFETY. If you chose to repair and figure out the issue ourselves, then wear your protection right and be cautious when handling electrical outputs. If it looks too risky for you, let the experts deal with it.
This is all where the switch operates the motor directly. If a relay or controller is involved, it will be different. Check the switch for continuity on all posts/wires with the switch NOT powered, first. Some other RV slide-out issues are not only easy to diagnose, but they are usually not complicated to repair.
Disconnecting from Shore Power
Circuit breakers can flip sometimes seemingly for no reason. A variety of electrical issues could cause RV’s slideout to malfunction. They could be anything from faulty writing or weak battery, to system overload that could have tripped your breakers or blown a fuse.
If you still do not get the desired results, have a professional check the motor for wear or loss of power. This happens when there is a loose electrical connection. If you do not have the skills, have a qualified electrician replace the motor for you. With a multimeter, test the supply terminals to see if the right amount of current is flowing to the motor.
Double-Check The Power Source
In their turn, the batteries are charged by the RV converter with takes in 110V AC and converts it into 12V DC used by RV batteries. Some AC portable generators also have DC outlets, so if you are using such a generator, the problem may lie in it. Now, even if you restore power in the RV, you aren’t quite done yet. The purpose of fuses and breakers is to protect the RV and its occupants from harm if an appliance or electrical lines draws too much current. The direct current system also knows as DC which generates power to operate lights and more. The converter can charge the batteries whenever the power stored gets low simply by using the AC Voltage and convert it to usable 12 voltage direct current receiver.
The most common cause for this problem is usually a misalignment in the electrical motor gears. There could also be an electrical issue that causes a broken circuit during sliding out. This would cut the power required to retract the slide in. This happens mostly with two-position momentary arm switches.
How do you restore electricity?
Why would the other two slides close, but not the bedroom one? We had a few years of experience under our belt and never faced this issue before. Should all else fail, you might have to manually disengage the slide-outs drive motor and manually crank or push the stuck slide-out section into place. This is another one of those times where you will need to manually close the slide-out section and have it repaired by a professional when you get back home.
Do RV slides work on battery?
Go and visually check the path of your slide to make sure it is clear. If you have your rig professionally maintained, make sure the shop performs this task. You paid a lot for your camper, and you want it to work correctly for a long time.
English 
Romanian