Light My Fire Fire Lighting Kit

If you are using a 50cm Connecting Cable from the fire truck, connect it into the 2nd or 3rd port from the left of the 12-Port Expansion Board. To test the lights, connect the 50cm Connecting Cable to the 12-Port Expansion Board. Connect the USB Power Cable to it and connect the other end to your power source. 1) Start by removing the following pieces to allow us to remove one of the headlight sections from the front. This section will guide you to install light to the fire truck first. When installing Bit Lights under LEGO® pieces, ensure they are placed the correct way up .

5.) We will now install lights to the 2 front door lamps. First remove the following pieces to allow us to gain access. Thread the lamp post cable underneath the front wall and then pull it all the way through from the inside of the building. Ensure the cable is laid neatly in a straight line in between the studs of the base plate. Reconnect the grey plate with clip to the trans red piece and then reconnect this section back to the black frame. Ensure the cable is threaded behind and then back through the black frame toward the front.

LIGHT MY FIRE Lighting Kit

Take a LED Strip Light (striplight#3) and stick it to the following position underneath this section. I’ve chosen to stick the strip light rather than mount using LEGO plate as I don’t want the strip light to be too visible. 8.) We will now install a light above the gold fireman hats on each side of the front. First, remove a few of the tile pieces and then disconnect the grey 2×4 plate. Reconnect the lamp shade piece to the trans yellow brick, securing it in place. Ensure the cable is facing toward the back and then reconnect back to the wall section.

Pull the cable through from the inside of the building. 4.) In order for us to thread the cable through to the inside of the building we will need to make a gap in between bricks. Using the LEGO removal tool, lift up this section of the wall to create an opening. Reconnect this whole section back to the truck ensuring the cable is laid underneath the bottom of the black frame toward the back. 6.) Feed the wire behind and in between the grey stud before reconnecting the grey brick with bar over the top.

Related Products to Light My Fire Lighting Kit

We can’t install lights to these pieces so we will be replacing them with different pieces . 2.) Replace the stock lamp post with the Light My Bricks lamp post with Bit Light installed then carefully bend the corner of the base plate down so that it comes apart from the front wall. Thread the cable up to the back section of the fire truck and pull all the way up from the top.

You can either place them directly on top of LEGO® studs or in between. Always ready for a sip on the go and a drink in the wild.The Pack-up-Cup is a portable, collapsible solution for travelling, camping and everyth.. Extend your adventurous outdoor menu with a portable and adjustable grill. Compact, practical, portable and a brilliant way to exte.. Light My Fire Fire Lighting Kit is part of our greater selection of .

Light My Fire FireLighting Kit – Pink/Orange

All-natural tinder, chemical free with up to 80% resin content. These pines are cultivated and do not occupy rain forest areas. They are a non-endangered species, yielding a product that is sustainable, economically viable and environmentally responsible. By making use of the stumps, we are reducing overall waste while creating a sustainable and safe by-product. Verified under the SCS Salvaged Wood & Fiber™ standard for using 100% reclaimed material. Light My Fire makes flint and steel to light fires while camping, hunting, cooking out, hiking, or in an emergency.

Ensure the cable is laid in between studs before then closing the gap of the wall and connecting everything back together. Take a White Flashing 15cm Bit Light and then place the LED component directly over the red stud. Secure it in place by reconnecting the trans blue round brick over the top.

Related Products to Light My Fire FireLighting Kit

Light my Fire Collapsible Pack-Up Water BottleCollapsible for easy transport. Light My Fire – Lunchkit BIO 6 PCSAll you need to bring your own, eat in style, and pack away again. Campingaz – Twister Plus PZCompact cooker with one burner that is easy to transport and store during trips. The primary advantage of a Swedish FireSteel fire starter over other fire starting tools is reliability in any situation.

The Swedish FireSteel fire starter is robust and requires no flints, lighter fluid, batteries or replacement parts. All you need to light a fire and get your hotdogs cooking.

EXPEDITED SHIPPING on Over 250,000 Products

Reconnect this section back to the back of the truck and discard the flat red plate as this is no longer needed. Incorrectly inserting the connector can result in bent pins inside the port or possible overheating of the expansion board when connected. Take extra care when inserting connectors to ports on the Strip Lights.

Secure the bit light in place by reconnecting the trans red round plate over the top. First developed for the Swedish Department of Defense, the legendary Swedish FireSteel fire starter is the original magnesium alloy fire starter. The Swedish FireSteel fire starter offered the first viable solution to the challenges of starting fires at high-altitudes and in low temperatures.

Light My Fire Fire Lighting Kit Similar Products

It is our advice to investigate the recycling system available to you at your local centre, and make your decisions based on the information we provide and that of your communities recycling facility. You can find a full report for each product including its material composition and how to dispose of it responsibly within our materials pages. Together we can make the right decisions based on open communication and understanding. Lift up a few of the dark grey Lego pieces surrounding the door and then thread the battery cable down below in between this gap. 23.) Take another 2x LED Strip Lights (striplight#4 and striplight#5) and connect them together using another 15cm Connecting Cable.

18.) Lift the top floor up over the bottom floor and then connect the other side of the cable from striplight#2 to one of the spare ports on the 12-port expansion board. 15.) It is now time to test our current lighting we have installed so far. Take the AA Battery Pack and insert 3x AA batteries to it. Connect the battery cable into one of the spare ports on the 12-port expansion board and then turn ‘ON’ to verify all is working OK. 5.) Take another White 15cm Bit Light and place the LED component directly over the stud of the red plate with clip.

Related Products to Light My Fire Fire Lighting Kit

Secure the cable by reconnecting the 1×6 plate we removed earlier. Turn the fire truck onto its side and thread the bit light cable over the wheel. Pull all the way through from the other side of the wheel.

Light My Fire Fire Lighting Kit Green

Flat and Round Battery Packs have been removed as of June 2022 due to child safety regulations.Please use the 50cm Connecting Cable in place of the Battery Packs. 2.) Turn over again and remove the two grey 1×6 plates. Here is the instructions document for the LEGO Fire Brigade LED lighting kit. • All natural and environmentally-friendly fire starter. The Light My Fire Fire Lighting Kit is a quality addition to the Light My Fire lineup. For more great deals on Guidebooks by Light My Fire, please browse our Light My Fire Camp & Hike page.