One Piece Or Two Piece Fishing Rod

Here’s everything you need to know about One Piece Or Two Piece Fishing Rod. Find all the information it in this article.

This influenced fishing rods across the entire planet. If the introduction to this article makes you think that I’m a bit partial to multi-piece rods then you’d be correct. The factors influencing a person’s choice between either a one-piece fishing rod or a two-piece fishing rod should get more discussion time than they do. I weighed this same decision two months ago, and the previous responses pretty well laid out the pros and cons. I think the answer boils down to how you transport your rod to and from the fishing grounds. In my case, the ability to break the rod in two pieces will decrease the odds that I accidentally convert a one-piece rod to a two-piece rod.

It is my understanding from hanging out here for awhile that Brown put the FLGR in the Custom Classic because a lot of folks just thought the top end model should have a FLGR. Whether or not they cycle any smoother is open to debate. I think there’s a bit of psychology involved. If you tell people a FLGR cycles smoother, it feels that way. IMHO the standard GI guide rod is the option to go with.

Is A One Piece Fishing Rod Better Than A Two Piece?

If tranportability wouldn’t have been an issue , I would have gone with the one piece. It doesn’t make that much of a difference, although with the two piece rods, you sacrafice some sensitivity, strength, and a consistent taper for the convenience of being able to pack it easier. The standard Brown setup is the GI guide rod. I don’t think the Custom Classic always had the FLGR but I could be wrong.

If the model your looking at fits all your needs then I wouldn’t even think twice about getting it just because its a 2 piece. Then there is the pile of older rods in the corner….. It’s kind of hard getting that 10′ one piece in the back seat. Doing a 3-piece would help keep the cost down. That’s highly variable depending on what needs to happen, if guides need to be re positioned, etc.

How To Fish Fort Morgan Alabama From Shore

I have had the same Ugly stick for 30 years. I love of even better thant the Shakespeare one piece I had as a youngun. It seems trivial to me, ease of breaking down is the sole reason. My full size 1911, has the full length, 1 piece, I was just wondering what the reasoning is for the 2 piece. I really don’t know what precipitated the two piece. I lock together and shorten them to the one piece length.

With a two piece rod you will lose sensitivity and you will have a weak point in the rod. If you are fishing from a boat, you will not need a long rod. The longer the road, the further you can cast. However, it’s not that big of a difference in casting length. I have a 7ft rod, but it’s for muskie fishing .

How Do You Know If Your Rod Is Sensitive?

A short rod is ideal if you want to make short, accurate casts. When pinpoint accuracy is less critical, a long rod is the way to go. Dingy or dirty water and heavy cover are two situations where short-range accuracy is part of the recipe for success, and a shorter rod can really shine. Ok, so for a straight up 1911 with the usual endowments, a Full length GI guide rod is what we know works time and time again and it makes no sense to switch. A good 2-piece rod will leave you forgetting that it isn’t a one piece.

Constructing a glass ferrule is not all that hard but you need the right blank material with the right wall thickness and ID that will fit the rod your cutting. That means checking a bunch of scrap stock . I had a customer in Germany that wanted me to do the same thing. I looked for a similar blank in a two piece version but couldn’t find one to fit his needs. I flat out refused to do it, just didn’t feel comfortable doing it and didn’t want to void the blank warranty.

Traveling With 2 Piece Fishing Rods

Instead, you should clean both connecting sections often with a clean rag or ear swabs and fresh water. Below are a few pieces of helpful info that I wish I had when I started using surf rods. Let’s further break down 2 piece rods vs 1 piece rods, and find out what you actually gain and what you give up with each. If you are looking at two piece rods because of their more compact size, you may also want to consider telescoping rods. +1, and you can avoid losing pieces of your multi-piece rod by applying wax to the male section that goes into the ferrule.

Personally I have gone 4 piece or tele. I catch infinity more fish having a compact rod stashed in the car boot with me when the main purpose of the trip is not fishing, than I would with a 1 piece – which would be in the shed at home. I prefer one piece, bot have a six foot bed on my truck so two piece it is. Now I use 1 piece for light stuff but I’ve got a 24kg T-curve spin rod which is two peice but I don’t think such a good rod would give me any troubles. With the amount of torque you’re throwing a baitcaster, like Al says, sooner or later that 2nd piece is going to work its way loose and you will be casting it. There are one piece FLGR, two piece FLGR, and the GI rod and plug.

Or 2 Piece Rods

End result is he agreed with me and settled on a one-piece. I’m looking for suggestions on the best way to do this. I’m sure these are very nice rods and I sure don’t want to screw up… I’m thinking about ordering the AmTack brass ferrules and trying to figure out how to fit them.

Peice Rods Vs 2 Peice Rods

Rods like modern surf rods and fly rods are most often joined in the middle. Whereas offshore boat rods (bottom bashers, stand-up bent butt game rods, and some jig sticks) and longer lure casting rods are some of the more common styles of multi-piece rod. They have fast action and lots of heft to chuck big lures and handle the larger toothy critters. I also use these rods for casting lures like Gottcha plugs when I am at the ocean and fishing for blues and spanish or big chunks of bait for the bottom feeders like puppy and black drum. I have both, and tend to buy 2 piece rods anymore. I have been at this game for too many years, and to tell the truth, i can’t feel any difference when it comes to sensitivity.

Properly Assembly Of A 2 Piece Fishing Rod

Some will say that a “one piece/two piece FLGR” helps with the recoil spring from any possible binding. For me it is easier on field stripping with the GI guide rod, Had a two piece on a Springer and a one piece on a Kimber, after several cleanings….out they went. What you may want to do upon ordering is request a one piece FLGR and have them provide a GI guide rod as well.

Fishing Rods: One Piece Or Two Piece

In the end, you won’t notice a difference. I think we are mainly talking preference here. I think there is a bit of fishing snob in all of us today that has to have the latest and greatest. One piece, 2 piece, 6 piece, fish don’t care. If the rod is going to be over 8 feet then I want it to be 2 piece. I just get clumsy transporting things and I could see myself breaking an 11 ft rod coming in and out of my home.

Can You Make A One Piece Fishing Rod Into A Two Piece?

Fine for casting but I would not recommend them for trolling. I think sometime in the area of rods and reels you do not always get what you pay for. I have a friend who repairs them I see a awful lot of expensive failures. Old timers would say that you may as well as buy a one-piece rod because when your two-piece rod’s metal ferrule corroded together then you’d end up with a one-piece rod anyway.

Vs 2 Piece Rods

Used to be, with older technology, that sectional rods didn’t have the even distribution of stress along the spine and they didn’t cast as well as a one piece rod. Instead of tying a knot, however, run the tag end of line through the rod tip first, through the loop second, then snug it up. (The loop should now be tight against the rod tip. See photos below.) Testing fishing rod sensitivity is easy in your store with a short section of mono attached to the rod tip . I shot with one that came with one of my Springers one time before I changed it. In that case, I was able to field strip it without using the allen wrench for the guide rod……. The other guide rods were really built just to have a product to sale, They do not add any accuracy, they don’t really make take down any easier, and they don’t add any reliability.

They’re also easier if you have to hike through the woods to get to a fishing spot. 1 piece is sturdier since it’s all one piece and can distribute the load of a big fish evenly. If a two piece rod fails because of a big fish, it usually blows out right above or below the ferrule where the two pieces connect.

One piece is imo the best investment but for convenience sake, an afterthought as it becomes cumbersome to travel with in some cases. But the force on the joint of any rod can be compromised if it is not checked periodically. Anyway, if i am plugging or am flyrodding i am taping the sections with electrical tape as to keep the integrity of the rod in tact so as to avoid any unwanted incidents of such nature to occur.